
Upgrade: Enclosure
Easy30 to 45 min26 steps
- Note: Take the left panel and remove the protective film from it.
- Note: Prepare the panel by loosely adding onto it fasteners.
- M4 x 8mm Bolt (x8)
- M4 T-nut (x8)
- Caution: Match the orientation as shown in the diagram about which side the bolts and nuts should be on.
Loading comments…
- If you have already got print heads installed then you will need to break the cable ties on the lower part of the tool dock bracket and slide the panel in from the front of the printer.
Loading comments…
- Note: Take the right panel and remove the protective film from it.
- Note: Prepare the panel by loosely adding onto it fasteners.
- M4 x 8mm Bolt (10)
- M4 T-nut (10)
- Caution: Match the orientation as shown in the diagram about which side the bolts and nuts should be on.
Loading comments…
- Install the panel to the right side of the frame.
- Temporarily unmount the camera from the frame to install.
Loading comments…
- Note: Take the rear panel and remove the protective film from it.
- Note: Take the 70mm blower fan and fix it to the panel.
- M4 x 40mm
- M4 Nyloc Nut
- Feed the fans cable in through this hole.
- Caution: Make sure to install the fan on the side shown in the diagram.
Loading comments…
- Note: Install the 3d printer fume filter fan shroud.
- M4 x 40mm Bolt
- M4 Nyloc Nut
Loading comments…
- Note: Prepare the panel by loosely adding onto it fasteners.
- M4 x 8mm Bolt (x11)
- M4 T-nut (x11)
Loading comments…
- Install the rear panel as shown to the back of the printer.
Loading comments…
- Note: Prepare four 3D printed door handles:
- 3D Printed Door Handle
- M3x10x2mm Countersunk Magnet
- M3 x 8 CS bolt
- Reminder: Self tap the bolt into the hole on the 3d printed part.
Loading comments…
- Note: Take the two front door panels and remove the protective film from both of them.
- Fix onto both door panels two handle assemblies as shown.
- M3 x 10mm Bolt
- Reminder: Self tap the bolts into the holes on the 3d printed part.
Loading comments…
- Fix two hinges onto each door panel as shown. The hinges should be installed on the front side of the panel.
- Hinge
- M4 x 10mm Bolt
- M4 x 8mm Bolt
- M4 Nyloc Nut
- M4 T-nut
- Reminder: Fasten these on loosely.
Loading comments…
- Fix the two door latch brackets onto the front of the frame as shown. Install them onto the centre of the frame.
- Front door latch
- M4 x 8mm Bolt
- M4 T-nut
Loading comments…
- Fix the front doors onto the frame of the printer from the hinges.
Loading comments…
- Note: Begin by assembling the three roof panels as shown.
- Roof Front Panel
- Roof Left Panel
- Roof Right Panel
- M5 x 10mm Bolt
- M5 Nyloc Nut
Loading comments…
- Fasten on two more M5 x 10mm Bolts and M5 Nyloc Nuts.
Loading comments…
- Install the rear panel to the assembly.
- M5 x 10mm Bolt
- M5 Nyloc Nut
Loading comments…
- Add two more M5 x 10mm bolts and M5 Nyloc Nuts to the assembly as shown.
Loading comments…
- Add the support beam to the roof assembly.
- M5 x 10mm Bolt
- M5 Nyloc Nut
Loading comments…
- Remove the protective film from both sides of the acrylic panel and fix it onto the roof as shown.
- M5 x 10mm bolt
- M5 Nyloc Nut
Loading comments…
- Fix on the two metal support bracket as shown.
- M5 x 10mm Bolt
- M5 Nyloc Nut
Loading comments…
- Note: Repeat the process with the larger acrylic panel.
Loading comments…
- Mount the handle onto the front of the roof assembly.
- M4 x 8mm Bolt
Loading comments…
- Note: Fix the 3D printed Stopper to the roof assembly.
- 3D Printed Stopper
- M5 x 20mm Bolt
- M5 Nyloc Nut
Loading comments…
- Note: Add to the rear of the assembly two hinges.
- Hinge
- M4 x 10mm Bolt
- M4 x 8mm Bolt
- M4 Nyloc Nut
- M4 T-nut
- Reminder: Loosely fasten on the T-nuts
Loading comments…
- Cut the foam tape into four sections and stick them onto the top of the frame as shown.
Loading comments…
- Mount the roof assembly to the frame by the hinges as shown.
Loading comments…